We have for our client commercial wet grinding pulveriser that have fully machined & balanced beaters. These commercial wet grinding pulveriser are popular for continuous crushing and suitable for wet-pulpy. Offered in compact size commercial wet grinding pulveriser do not require too much space. Our commercial wet grinding pulverisers are used for grinding different types of product like Tomato, fresh ginger, onion, garlic, sugar, fresh fruits, vegetables, beetle nuts, leaves, Wet rice, wet pulses, wet dal, and allied food production.

The different standard accessories available with Wet pulveriser : -
*Set of 4 perforated round hole Stainless Steel screens are supplied with Wet pulveriser
* 3-meter cable with plug with miniature circuit breaker will be fitted for overload protection for motor
*One brush for cleaning of commercial wet grinding pulveriser

Key Features of wet pulveriser :

• Unique and Reliable Design
  • The Wet series pulveriser are highly effective as well as non stop continuous pulverizing process.
• All contacting Parts are Aluminum & Stainless Steel no corrosions hazards
• Spice Mill is not required any V belts thus less friction losses.
• Increased production leading to faster return on the investments

• All Rotating parts are dynamical balanced for less vibration & higher performances.

• low temperature grinding technology thus the original ingredient cannot destroy.

Operations of Wet pulveriser : -

The flow of material from the Feeding Hopper is regulating by means of side handle easily to suit the load. Rotor runs in anti-clockwise direction. The beaters pass just beneath the Ratchet Teeth Liner fitted inside the top half of the crushing chamber, leaving a gap of 3 mm between the liner teeth and the tips of the rotating beaters. This cuts the material caught between the liner teeth like a sword with a scissors action at a 2880 R.P.M. After the required size reduction, the material will pass through the screen fitted inside the lower discharge end of the grinding chamber. No sieving is required, as the appropriate size screen fitted will not allow coarser material to pass through. The air generated in the crushing chamber forces the powder to pass through the screen fitted at the bottom discharge end of the crushing chamber, into a Filter attached to the delivery trough below. (When crushing Wet-Pulpy materials, the balloon should not be use)

Servicing Guidelines of Wet pulveriser :-

Open the cover of chamber all grinding parts cleaned with a brush in couple of minute and the pulveriser is ready for next crushing. If required, the grinding chamber can also be wash with water. Remove the cotton balloon and the screen, close the cover tightly and start the pulveriser. Now pour a bucket or two of water into the hopper. The grinding parts will be flushed with the water and cleaned. Continue running the machine for a few more minutes as the draft of the fresh air sucked into the pulveriser will dry it. The beater when worm out removed and reserved by removing the cur clip lock holding to the rotor pins. When both the edges are worm out, they sharpened on an emery stone, to be use as new. In addition, when completely warn out, replaced the equal weight and refitted.

Standard Accessories of Wet pulveriser

• Four numbers of Screens
• Suitable three phase or Single Phase Sq. cage motor {Electricity (Special power can be accommodated): 220/380/415 V0lts, 50/60 Hz , 3 Phase }.
• Three meter cable Suitable miniature circuit breaker as per IS: 8828 with 3 meter cable & 3 pin top as per IS: 1293 for single Phase Electric Motors. or three meter four core cable with starters, for Three Phase Electric Motor.

Extra Accessories of wet pulveriser

• Suitable totally enclosed fan cooled three phase Sq. cage motor as per IS: 325. {Electricity (Special power can be accommodated): 220/380/415 V0lts, 50/60 Hz, 3 Phase }
• starters, main switch, ampere meter, capacitor For three phase
• foundation bolts
• V Belts
• All Contacting Parts Stainless Steel 304 / 316 can be accommodated

Application of wet pulveriser

Wet grinding pulveriser are exclusively meant for the grinding of chili, Coriander, Dry ginger, Black Pepper, Turmeric and Curry powders, on a large scale basis. These spices are ground in a two / three stage operation, depending on the fineness desired, i.e. The breaking of the Turmeric in a large hole screen for the first operation, and the subsequent fine grinding done in a fine hole screen for the second and third operation. We give here below production figures for the same.

Construction of Wet pulveriser

Wet pulveriser Made from heavy duty Stainless Steel fabricated body. Stainless Steel Grinding Chamber lined with serrated wear stainless Steel plates, which protects the body from wear and tear. Grinding done by a set of Fixed better on a balanced rotor. A screen classifier forms the lower half of the grinding chamber.

Available Models of Wet pulveriser

Model No	Jas 1202	Jas 1203
Chamber Size	200 mm X 100 MM	200 mm X 200 MM
Pulverizer's RPM	2880	2880
Motor H.P. ( KW.)	1 H.P. (0.75 Kw.)	2 H.P. ( 1.5 Kw.)
Pulverizer's Dimensions	48 X 33 X 63 CM 36 kg.Approximate	55 X 40 X 90 CM 59 Kg.. Approximate